Stretchable Composite Acoustic Transducer for Wearable Monitoring of Vital Signs

A highly flexible, stretchable, and mechanically robust low‐cost soft composite consisting of silicone polymers and water (or hydrogels) is reported. When combined with conventional acoustic transducers, the materials reported enable high performance real‐time monitoring of heart and respiratory patterns over layers of clothing (or furry skin of animals) without the need for direct contact with the skin. The approach enables an entirely new method of fabrication that involves encapsulation of water and hydrogels with silicones and exploits the ability of sound waves to travel through the body. The system proposed outperforms commercial, metal‐based stethoscopes for the auscultation of the heart when worn over clothing and is less susceptible to motion artefacts. The system both with human and furry animal subjects (i.e., dogs), primarily focusing on monitoring the heart, is tested; however, initial results on monitoring breathing are also presented. This work is especially important because it is the first demonstration of a stretchable sensor that is suitable for use with furry animals and does not require shaving of the animal for data acquisition.     

High‐performance printable paper‐like composites derived from plastic flexible film wastes

Owing to lack of proper recycling methods, plastic flexible film wastes are usually directly discarded or incinerated, which brings about severe environmental pollution. Therefore, converting plastic wastes into value‐added products has received more and more attention in recent years. In this work, paper‐like composites derived from plastic flexible film wastes were prepared via the thermally induced phase separation method by adding polyethylene‐graft‐maleic anhydride (PE‐g‐MAH) as a compatibilizer and fumed silica as an additive. The resulting paper‐like composites were characterized by SEM and infrared spectroscopy. Other properties such as mechanical properties, thermal properties, whiteness, printability and adsorption performance were also tested in detail. It was found that remarkable enhancements in mechanical, thermal and printable properties of the paper‐like composites were obtained when nano‐SiO₂ loading was 2.5–3 wt%. Uniformly distributed holes that can endow good printability by providing space for ink or other functional molecules were observed by using SEM. Furthermore, the CIE whiteness value of the resulting composites can reach 91.6%–96.7% on adding nano‐SiO₂. Additionally, the paper‐like composites integrating nano‐SiO₂ and PE‐g‐MAH exhibited good solid ink affinity and high water or oil adsorption capacity. Thus, according to this research, high‐performance printable paper‐like composites used as major components of multifunctional papers can be prepared based on plastic flexible film wastes. © 2019 Society of Chemical Industry     

柔性钙钛矿太阳能电池的制备及性能研究

采用钛箔作为衬底,原位生长二氧化钛薄膜,然后制备有机钙钛矿吸收层及固态空穴传输层,组装成太阳能电池。通过电压-电流曲线测试,结果表明,这种钙钛矿太阳能电池的光生电压达到0.8 V、光生电流达到16 mA/cm²、光电转化效率为10.2%。进一步对电池进行弯折试验,弯折20次后,光电转化效率能达到初始值的85%,表现出良好的柔性特征。     

Flexible and transparent capacitors based on gel-type natural polymers

In this work, we study the capacitive properties of gel-type natural abundant polymers without any dopants, mainly commercial gelatin and agar in deionized water. Here, we propose a facile fabrication of flexible, transparent, and planar electrolytic capacitors using these gel-type and indium tin oxide thin films as electrodes deposited on poly(ethylene terephthalate) substrates. Through cyclic voltammetry and galvanostatic charge–discharge techniques, we found that the devices show a specific capacitance in the order of the millifarads per gram, a specific power of ~10 mW cm⁻², which is sufficient to active low-power devices, and a life cycle with nearly 100% efficiency after 1,000 cycles. We found that we do not need to add dopants that improve the ionic conductivity of the natural polyelectrolytes to obtain capacitances within the millifarads per gram. The flexibility of the capacitors was demonstrated by bending them, after which they exhibited the same electrochemical performance as the unbent devices. The optical transparency of the capacitors was measured by UV–V is spectroscopy showing a high transmittance in the visible region.     

Adaptive robust boundary control of shaft vibrations under perturbations with unknown upper bounds

This paper presents robust and adaptive boundary control designs to stabilize the two‐dimensional vibration of hybrid shaft model. The hybrid shaft is mathematically represented by a set of partial differential equations, governing the shaft vibrations, coupled to ordinary differential equations, describing rigid body spinning and dynamic boundary conditions. The control objective is to stabilize the transverse vibrations of the perturbed shaft while regulating the spinning rate. To achieve this, the paper first establishes robust boundary control laws that fulfil the control objective in the presence of modeling uncertainties and external disturbances operating over the shaft domain and boundary. Lyapunov‐based analyses show that the proposed robust control exponentially stabilizes the shaft with vanishing distributive perturbations, while assuring ultimately bounded vibrations in the case of nonvanishing perturbations. Then, adaptive control philosophy is utilized to achieve redesigned robust controllers that only use online adaptation of control gains without acquiring the knowledge of bounds on perturbations, as well as dynamic parameters. An advantage of this design is avoiding an overconservative robust control law, which may induce poor stability and chattering in tackling system perturbations with unknown upper bounds. Simulations through finite element method illustrate the results. Copyright © 2014 John Wiley & Sons, Ltd.     

向家坝二纵围堰柔性结构段基础施工技术初探

向家坝水电站二期纵向围堰上游段座落于厚达45～62 m的覆盖层上，为提高接头段深厚覆盖层地基承载力，且保证导流期不同江水位时的堰体稳定，优化调整方案为，将接头段和导水段改为柔性结构。详细介绍了柔性结构段基础处理中所涉及的施工程序、施工技术和异常情况处理等。二纵围堰经过了2009年和2010年两个汛期的考验，安全监测显示与实际运行表明，柔性结构体结构稳定。将导水结构堰体改为柔性结构体，不仅节约了投资，而且保证了二期截流工程按施工总进度计划实施。     

Coil‐Type Asymmetric Supercapacitor Electrical Cables

Cable‐shaped supercapacitors (SCs) have recently aroused significant attention due to their attractive properties such as small size, lightweight, and bendability. Current cable‐shaped SCs have symmetric device configuration. However, if an asymmetric design is used in cable‐shaped supercapacitors, they would become more attractive due to broader cell operation voltages, which results in higher energy densities. Here, a novel coil‐type asymmetric supercapacitor electrical cable (CASEC) is reported with enhanced cell operation voltage and extraordinary mechanical‐electrochemical stability. The CASECs show excellent charge–discharge profiles, extraordinary rate capability (95.4%), high energy density (0.85 mWh cm⁻³), remarkable flexibility and bendability, and superior bending cycle stability (≈93.0% after 4000 cycles at different bending states). In addition, the CASECs not only exhibit the capability to store energy but also to transmit electricity simultaneously and independently. The integrated electrical conduction and storage capability of CASECS offer many potential applications in solar energy storage and electronic gadgets.     

Optimizing the lignin based synthesis of flexible polyurethane foams employing reactive liquefying agents

The present work is focused on the optimization of a green process based on the employment of by‐products obtained from wood treatments as raw materials for producing flexible polyurethane foams. More specifically, lignin was employed in flexible polyurethane foams in order to partially replace the usual fossil polyols; therefore glycerol (GLY) and glycerin polyglycidyl ether (EJ 300) were used as the polyol fraction for lignin liquefaction. Polypropylene glycol triol was used as a chain extender in different ratios with liquefaction solvents, and polymeric diphenylmethane diisocyanate as an isocyanate fraction. Liquefaction of lignin was performed by microwave irradiation, thus reducing the processing time and energy required compared to present industrial production processes. All the foams were produced in controlled expansion through the adoption of a ‘one‐shot’ approach, using water as a blowing agent and with an isocyanate index (NCO/OH) of less than 100 to improve the flexibility of the foam. This approach allowed for the substitution of up to 12% of common petro derived polyol with commercial soda lignin. Finally, the foams were characterized, presenting properties that could be modulated as a function of lignin content, GLY/EJ 300 ratio and isocyanate index. The qualities of the foams were compatible with existing materials used for furniture and for the interiors of car seats and couches. © 2015 Society of Chemical Industry